相关推荐
Is it possible to use the products in a transfer molding method?
No, they are not usable. Even in the case of resin molding method, please contact us beforehand.
Is it possible to convert two CCP2s to a transfer switch or by-pass switch like I do for the ABB switches?
No, there is no means available to mechanically interlock two CCP switches to perform these functions.
Is it possible to convert two CCP2s to a transfer switch or by-pass switch like I do for the ABB switches?
No, there is no means available to mechanically interlock two CCP switches to perform these functions.
Renesas有集成lin transfer 的mcu么
RENESAS MCU暂时没有集成LIN Transfer的MCU产品。
For BD37033FV-M,BD37034FV-M,BD37524FS,BD37534FV,BD37543FS, What is the level meter function?
The Level Meter is a circuit that outputs a DC voltage proportional to the magnitude of the signal and holds the peak level of the detected signal. Since the held peak level can be reset by resetting the Level Meter, the transition of the peak level can be monitored by periodically performing a reset. The reset interval should be at least one cycle of the frequency to be monitored.
BD57020MWV-EVK-002 BOM无线电源传输组
本资料为ROHM公司提供的BD57020无线充电评估板（Evaluation Board）的物料清单（BOM），包含用于该评估板的各个组件及其规格。资料详细列出了所需元件的品牌、型号、数量、尺寸和封装类型，并附带了使用注意事项。
ROHM - MCR03EZPJ332,MCR03EZPFX1501,GRM21A7U2E102JW31,MCR18EZPJ120,MCR03EZPFX1004,MCR10EZPF3302,MCR03EZPFX3302,RQ1E070RP,MCR03EZPJ152,MCR03EZPF1R00,ML610Q772,BD57020MWV,MCR03EZPFX1001,EDZVT2R6.2B,RQ3E100GN,NX3225GA,ML-P11VT,GRM32D7U2E333JW31,MCR03EZPF200,MCR03EZPJ204,MCR03EZPJ105,MCR03EZPF205,MCR03EZPJ102,MCR03EZPJ202,MCR03EZPJ103,MCR03EZPJ104,MCR03EZPJ302,MCR18EZPJ470,DLW5BTN101SQ2L,MCR03EZPFX4701,MCR03EZPJ363,EDZVT2R6.8B,MCR03EZPFX2701,SML-P11MT,INA199A1,EDZVT2R4.3B,UCR18PVHXFLR100,MCR03EZPFX6201,BU7241G,RE1C002UN,RB530VM-30,MCR03EZPFX103,RUR020N02
For Analog Audio Processors, Do I also need to set the registers to its initial values?
When power is turned on, be sure to send data to all addresses as initial data. It is also recommended to mute the device until the initial data is transmitted.
How can the start-up behavior be modified?
The way of the power state transition can be modified through the register of TRANS_COND0/1.
In the FSK mode, when continuously transmitting the modulated wave using RF_TEST_MODE, the center frequency shifts by about 3 KHz.
As described in the data sheet, when using RF_TEST_MODE in FSK mode, the modulator reads unnecessary data before the generation of the expected test data just after TX_ON is started up. Therefore, the center frequency changes. To use RF_TEST_MODE correctly, check again through the following procedure. 1. Initialization register setting 2. Execute VCO_CAL 3. TX_ON 4. After starting up TX, MODEM reset * Note: Usually, this event does not occur when transmitting packets containing DIO control. So, it is not required to perform a MODEM reset after TX_ON. This is also an event specific to FSK mode. There is no problem in GFSK mode. Related Products: ML7344/ML7406 family, ML7345 family, ML7404, ML7414
When reading data on the data flash assigned in Segment 2 with the assembler, data cannot be read if written as follows: L ER14,[ER8]
When reading data on the data flash assigned in Segment 2 with the assembler, specify "2" in DSR, and load with the addressing with physical segment. MOV R0,#2 ST R0,DSR L ER14,DSR:[ER8] Related Products: ML610(Q)40x, ML610(Q)42x, ML610(Q)47x, ML610(Q)48x, ML610Q10x, ML610Q11x, ML610Q17x, ML610Q30x, ML610Q35x, ML610Q38x, ML610Q41x, ML610Q43x, ML610Q46x, ML620Q13x, ML620Q15x, ML620Q416/ML620Q418, ML620Q503H/ML620Q504H/ML620Q506H, ML62Q12xx, ML62Q13xx, ML62Q14xx, ML62Q15xx/ML62Q18xx, ML62Q16xx, ML62Q17xx
在做自研烧录器，有三极管需求，需要一个40V以上的NPN管子，有没有合适的推荐？
可以看一下ROHM的DTC114ECAHZGT116 NPN 100mA 50V Digital transistor (Bias Resistor Built-in transistor) 资料参考/product/54901.html
关于线性稳压器， 如果Datasheet中没有输出电容器最大电容值描述，是否可以无限制使用？
加大输出电容器的电容，虽然稳定性会有所改善，但是需要注意其他特性。加大电容将会延长ON时的充电时间、OFF时的放电时间，将电源电压设为OFF时，输出和输出的电压就会反向，从而有可能会有大电流向IC逆流。使用大容量时，请考虑使用逆流旁路二极管及防逆流二极管。
I want to rewrite my data flash 10,000 times or more. Is it possible?
The number of data rewrite times indicates the number of erase times. Therefore, you can decrease the number of erase times by incrementally writing an address when the size of data to be written is small. For example, when the size of data to be written at a time is 16 bytes, the data can be written 128 times per two sectors (2,048 bytes), thus allowing 1,280,000 times (128 times x 10,000 times) of rewrite. Related Products: ML610(Q)40x, ML610(Q)42x, ML610(Q)47x, ML610(Q)48x, ML610Q10x, ML610Q11x, ML610Q17x, ML610Q30x, ML610Q35x, ML610Q38x, ML610Q41x, ML610Q43x, ML610Q46x, ML620Q13x, ML620Q15x, ML620Q416/ML620Q418, ML620Q503H/ML620Q504H/ML620Q506H, ML62Q12xx, ML62Q13xx, ML62Q14xx, ML62Q15xx/ML62Q18xx, ML62Q16xx, ML62Q17xx
关于高边开关IC和负载开关IC，请告知在搭载过电流检测电路的机型的Datasheet中的“指示灯输出波形”中，检测到过电流后在电流输出的状态下，输出电压变为0V的原因。
指示灯输出波形使用电子负载装置（恒流模式）测量。检测到过电流后，IC输出受到电流限制后，装置也会持续接通电流，因此输出电压为0V。
电子商城
现货市场
服务
可定制丙烯酸酯胶粘剂的粘度范围：250~36000 mPa·s，硬度范围：50Shore 00~85Shore D，其他参数如外观颜色，固化能量等也可按需定制。
最小起订量： 1 提交需求>
授权代理品牌：集成电路
授权代理品牌：分立元件
授权代理品牌：接插件及结构件
授权代理品牌：部件、组件及配件
授权代理品牌：电源及模块
授权代理品牌：电子材料
授权代理品牌：仪器仪表及测试配组件
授权代理品牌：电工工具及材料
授权代理品牌：机械电子元件
授权代理品牌：加工与定制
我要提问